Testosterone Sustanon 250mg ml Product Detail
Sustanon 250 Functions & Traits:
Sustanon 250 is a testosterone hormone. Although synthetic it is a perfect replica of the naturally produced primary male androgen testosterone. By the esters that are attached, this is what defines Sustanon 250 and differentiates it from other testosterone compounds. The compound carries a mixture of small and large esters in a precise dose. It is the precise dose of each of the four testosterone esters that make it. You could take four other testosterones and combine them in the same dosing strength but this would not make it Sustanon 250. This is important because there are underground labs that try to pass off other mixtures as Sustanon 250. The precise makeup of Organon’s product is as follows:
30mg Testosterone Propionate
60mg Testosterone Phenylpropionate
60mg Testosterone Isocaproate
100mg Testosterone Decanoate
Effects of Sustanon 250:
By now we should have a good understanding of the effects of Sustanon 250 simply by understanding its functions and traits. If you suffer from low testosterone and supplement with Sustanon 250 you will suffer no more; problem solved. Then we have performance enhancement, and we want to break down the effects of Sustanon 250 in a way that gives them a real life understanding.
During an off-season bulking cycle this is one of the best times to use Sustanon 250. High testosterone levels create the perfect atmosphere for muscle growth. Granted, the calories have to be there. If you’re not eating enough all the testosterone in the world wont’ help you grow. However, the combination of a well-planned diet and high testosterone levels will see tremendous advancements in lean tissue growth. Of equal importance, high testosterone levels will enhance your metabolic rate. Those who have higher testosterone levels will gain less body fat during their off-season than those who do not have higher testosterone levels. Make no mistake, you can still gain a lot of unwanted body fat if you’re not careful with your off-season nutrition, but high testosterone levels will give you the ability to make better use of this period in training.
Testosterone Sustanon 250mg ml Recipe
dosage:250mg/ml @ produce:100ml
Testosterone Blend powder 25g (18.75ml)
2% BA 2ml
20% BB 20ml
59.25ml Grapeseed oil
Testosterone Sustanon 250mg ml Heat Sterilization
The simplest method to clear a steroid solution of microorganisms is to heat sterilize it. The typical way to accomplish this is to place the steroid vial in an oven for 30 minutes (bake at 120°C/250°F). You should leave a needle sticking through the rubber top to equalize the pressure inside the vial, or it may break. Note that a higher temperature and duration are typically used for complete dry heat sterilization, but this is not practical for our purposes due to the potential degradation of vial components, and possibly even the drug components. Still, the recommended 30 minutes at 120°C/250°F should kill most bacteria, and can be regarded as a viable harm reduction strategy.
Some people prefer to use the top of the stove for heat sterilization, and submerge their anabolic steroid vials in a pot of boiling water (100°C/212°F). The vial is kept in the boiling water for approximately 20-30 minutes. While this temperature is sufficient for killing many forms of bacteria and other microorganisms, it is generally not considered the best method of sterilization. A higher temperature should be used. It can also be difficult to control the temperature if the vial rests on the bottom of the pot, which is in direct contact with the burner or heat source. Given these problems, it is preferred to attempt heat sterilization in an oven, as discussed above.
Note that trenbolone appears to break down at fairly low heating temperatures.374 Its degradation increases with temperature and duration. Some degradation may be notable even at 100°C/212°F. As such, trenbolone products should be heat sterilized under slightly different conditions than those recommended above. This typically involves baking the vial in an oven for two hours at 80°C/175°F. Again, an unattached needle should be placed in the rubber stopper to equalize pressure.
Testosterone Sustanon 250mg ml Syringe Filtration
Another way to attempt sterilization of a steroid solution is to use a filter. A filter is a device that uses a membrane with tiny holes to prevent particles from passing through. The smaller the holes are, the more effective the filter. For this method a disposable syringe filter is used. These are usually found in .45-micron and .22-micron micropour sizes. The .22-micron filter is preferred, as it allows for the removal of almost all forms of bacteria. A .45-micron filter is also acceptable, though more likely to pass certain strains of diminutive bacteria. Syringe filters can be ordered through many mail-order suppliers, which can be located through online search engines without much difficulty.
The procedure for using a syringe filter is fairly simple. First, make sure you have all of the necessary equipment: a syringe, two needles (minimum), a sterile syringe filter, and a new sealed sterile vial. If you are attempting to sterilize a standard 10 ml vial, it may be preferable to use a syringe large enough to draw the full solution. This will reduce the exposure of your product to air. If drawing more than 3 mL at a time, you will want an extra needle to use for equalizing the pressure (you should leave it in the rubber while drawing from the vial). Be careful not to touch critical surfaces (the exposed needle, rubber stopper) while filtering.
Begin by drawing the steroid solution into the syringe. When you are done, remove the needle and attach your newly unwrapped syringe filter. Attach a new needle to the end of the filter, and inject the solution into the new sterile vial. The sterile vial and new needle are very important, as using the original components would only expose the product to bacteria again. Use enough pressure to empty the syringe into the vial. Be careful, as too much pressure can break the bindings or filter. The process is slow, especially with a larger syringe or small .22-micron filter. Provided great care was taken not to contaminate the steroid during the process, the resulting solution should be free of bacteria.
Also, these sterilization methods are applicable to oil-based steroids only. Heat sterilization (as outlined here) tends to cause the rapid evaporation of solvents/antimicrobial agents in water-based steroids. The suspended (instead of dissolved) nature of the particles also makes them likely to jam a syringe filter. Previous testing suggests there is a high prevalence of bacteria in counterfeit and underground water-based steroids.375 Given this, it is generally advised to only use water-based steroids if they have been dispensed through legitimate supply channels.
Testosterone Sustanon 250mg ml Order Process
1. email or whatsapp us about what you need,quantity and destination.
2. we would answer your email in 12 hours with our best price.
3. If you think the price is workable, we would send you our payment information.
4. After we received your payment ,we would arrange the shipping for you
5. You would receive our package in 7-10 working days.
Testosterone Sustanon 250mg ml Our Advantage
1. Top Quality in the market, most product have the purity of 98%+ and some beyond 99%
2. Competitive price, we offer speical discount for large amount order.
3. Fast shipping ,we would deliver your product in 7-10 working days.
4. Free Re-shipping, we promise that you will receive your package
5. Security, we will not transfer any of your info to any third party.