Test Blend 450mg ml Product Detail
Testosterone Enanthate is a steroid hormone from the androgen and is found in mammals and other vertebrates,testosterone Enanthate is primarily secreted in the tests of mails and the ovaries of female, although small amount are also secreted by the adrenal glands, testosterone Enanthate is the principle male sex hormone and an anabolic steroid. Testosterone Enanthate effective for enhancing males specific sexual traits. Testosterone Enanthate plays a key role in the development of male reproductive tissue such as the testis and prostates. Testosterone Enanthate is used to improve testosterone deficiencies such as hypogonadism and sexual dysfunction with limited side effects.
Testosterone Cypionate is the longest-estered testosterone available today. It has a half-life in the body of 15 to 16 days and is found as injectable oil. Because it reacts in the body for so long, it can cause more water retention than other steroids and is best used as bulking compound in a stack. At the same time it is said to produce a slightly higher level of water retention, but not enough for it to be easily discerned. Of course when we look at the situation objectively, we see these two steroids are really interchangeable, and cypionate is not at all superior. Both are long acting oil-based injectables, which will keep testosterone levels sufficiently elevated for approximately two weeks.
Testosterone propionate is a commonly manufactured, oil-based injectable testosterone compound. The propionate ester will slow the rate in which the steroid is released from the injection site, but only for a few days. Testosterone propionate is therefore much faster acting than other testosterone esters such as cypionate or enanthate, and requires a much more frequent dosing schedule, in order to maintain stable blood levels. While cypionate and enanthate are injected on a weekly or bi-weekly basis, propionate is usually injected every second. The propionate ester can be very irritating to the site of injection. their body reacting with a pronounced soreness and low-grade fever that may last for a few days. The most common dosage schedule for this compound (men) is to inject 50 to 100mg, every day or 2nd day. As with the more popular esters, the total weekly dosage would be in the range of 300-700mg. As with all testosterone compounds, this drug is most appropriately suited for bulking phases of training. Here it is most often combined with other strong agents such as Dianabol, Anadrol, or Deca-Durabolin, combinations that prove to work quite well.
Test Blend 450mg ml Recipe
Raws Steroid Powder Ingredients: Testosterone propionate 30g, Testosterone phenylpropionate 60g,
Testosterone isocaproate 60g,Testosterone decanoate 100g,
Testosterone enanthate 100g,Testosterone cypionate 100g.
BA: 20ml ; BB:200ml ;
Then adequate GSO to make total volume of solution at 1000 ml
Test Blend 450mg ml Heat Sterilization
The simplest method to clear a steroid solution of microorganisms is to heat sterilize it. The typical way to accomplish this is to place the steroid vial in an oven for 30 minutes (bake at 120°C/250°F). You should leave a needle sticking through the rubber top to equalize the pressure inside the vial, or it may break. Note that a higher temperature and duration are typically used for complete dry heat sterilization, but this is not practical for our purposes due to the potential degradation of vial components, and possibly even the drug components. Still, the recommended 30 minutes at 120°C/250°F should kill most bacteria, and can be regarded as a viable harm reduction strategy.
Some people prefer to use the top of the stove for heat sterilization, and submerge their anabolic steroid vials in a pot of boiling water (100°C/212°F). The vial is kept in the boiling water for approximately 20-30 minutes. While this temperature is sufficient for killing many forms of bacteria and other microorganisms, it is generally not considered the best method of sterilization. A higher temperature should be used. It can also be difficult to control the temperature if the vial rests on the bottom of the pot, which is in direct contact with the burner or heat source. Given these problems, it is preferred to attempt heat sterilization in an oven, as discussed above.
Note that trenbolone appears to break down at fairly low heating temperatures.374 Its degradation increases with temperature and duration. Some degradation may be notable even at 100°C/212°F. As such, trenbolone products should be heat sterilized under slightly different conditions than those recommended above. This typically involves baking the vial in an oven for two hours at 80°C/175°F. Again, an unattached needle should be placed in the rubber stopper to equalize pressure.
Test Blend 450mg ml Syringe Filtration
Another way to attempt sterilization of a steroid solution is to use a filter. A filter is a device that uses a membrane with tiny holes to prevent particles from passing through. The smaller the holes are, the more effective the filter. For this method a disposable syringe filter is used. These are usually found in .45-micron and .22-micron micropour sizes. The .22-micron filter is preferred, as it allows for the removal of almost all forms of bacteria. A .45-micron filter is also acceptable, though more likely to pass certain strains of diminutive bacteria. Syringe filters can be ordered through many mail-order suppliers, which can be located through online search engines without much difficulty.
The procedure for using a syringe filter is fairly simple. First, make sure you have all of the necessary equipment: a syringe, two needles (minimum), a sterile syringe filter, and a new sealed sterile vial. If you are attempting to sterilize a standard 10 ml vial, it may be preferable to use a syringe large enough to draw the full solution. This will reduce the exposure of your product to air. If drawing more than 3 mL at a time, you will want an extra needle to use for equalizing the pressure (you should leave it in the rubber while drawing from the vial). Be careful not to touch critical surfaces (the exposed needle, rubber stopper) while filtering.
Begin by drawing the steroid solution into the syringe. When you are done, remove the needle and attach your newly unwrapped syringe filter. Attach a new needle to the end of the filter, and inject the solution into the new sterile vial. The sterile vial and new needle are very important, as using the original components would only expose the product to bacteria again. Use enough pressure to empty the syringe into the vial. Be careful, as too much pressure can break the bindings or filter. The process is slow, especially with a larger syringe or small .22-micron filter. Provided great care was taken not to contaminate the steroid during the process, the resulting solution should be free of bacteria.
Also, these sterilization methods are applicable to oil-based steroids only. Heat sterilization (as outlined here) tends to cause the rapid evaporation of solvents/antimicrobial agents in water-based steroids. The suspended (instead of dissolved) nature of the particles also makes them likely to jam a syringe filter. Previous testing suggests there is a high prevalence of bacteria in counterfeit and underground water-based steroids.375 Given this, it is generally advised to only use water-based steroids if they have been dispensed through legitimate supply channels.
Test Blend 450mg ml Order Process
1. email or whatsapp us about what you need,quantity and destination.
2. we would answer your email in 12 hours with our best price.
3. If you think the price is workable, we would send you our payment information.
4. After we received your payment ,we would arrange the shipping for you
5. You would receive our package in 7-10 working days.
Test Blend 450mg ml Our Advantage
1. Top Quality in the market, most product have the purity of 98%+ and some beyond 99%
2. Competitive price, we offer speical discount for large amount order.
3. Fast shipping ,we would deliver your product in 7-10 working days.
4. Free Re-shipping, we promise that you will receive your package
5. Security, we will not transfer any of your info to any third party.