Stanozolol (Winstrol) 50mg ml(water based) Recipe
Basic Recipes of 50mg/ml Stanozol
1 Gram winny powder
4.0cc PEG 300/400
0.6ml polysorbate 80
0.4ml benzyl alcohol
14.25ml distilled water
Stanozolol (Winstrol) 50mg ml(water based) Heat Sterilization
The simplest method to clear a steroid solution of microorganisms is to heat sterilize it. The typical way to accomplish this is to place the steroid vial in an oven for 30 minutes (bake at 120°C/250°F). You should leave a needle sticking through the rubber top to equalize the pressure inside the vial, or it may break. Note that a higher temperature and duration are typically used for complete dry heat sterilization, but this is not practical for our purposes due to the potential degradation of vial components, and possibly even the drug components. Still, the recommended 30 minutes at 120°C/250°F should kill most bacteria, and can be regarded as a viable harm reduction strategy.
Some people prefer to use the top of the stove for heat sterilization, and submerge their anabolic steroid vials in a pot of boiling water (100°C/212°F). The vial is kept in the boiling water for approximately 20-30 minutes. While this temperature is sufficient for killing many forms of bacteria and other microorganisms, it is generally not considered the best method of sterilization. A higher temperature should be used. It can also be difficult to control the temperature if the vial rests on the bottom of the pot, which is in direct contact with the burner or heat source. Given these problems, it is preferred to attempt heat sterilization in an oven, as discussed above.
Note that trenbolone appears to break down at fairly low heating temperatures.374 Its degradation increases with temperature and duration. Some degradation may be notable even at 100°C/212°F. As such, trenbolone products should be heat sterilized under slightly different conditions than those recommended above. This typically involves baking the vial in an oven for two hours at 80°C/175°F. Again, an unattached needle should be placed in the rubber stopper to equalize pressure.
Stanozolol (Winstrol) 50mg ml(water based) Syringe Filtration
Another way to attempt sterilization of a steroid solution is to use a filter. A filter is a device that uses a membrane with tiny holes to prevent particles from passing through. The smaller the holes are, the more effective the filter. For this method a disposable syringe filter is used. These are usually found in .45-micron and .22-micron micropour sizes. The .22-micron filter is preferred, as it allows for the removal of almost all forms of bacteria. A .45-micron filter is also acceptable, though more likely to pass certain strains of diminutive bacteria. Syringe filters can be ordered through many mail-order suppliers, which can be located through online search engines without much difficulty.
The procedure for using a syringe filter is fairly simple. First, make sure you have all of the necessary equipment: a syringe, two needles (minimum), a sterile syringe filter, and a new sealed sterile vial. If you are attempting to sterilize a standard 10 ml vial, it may be preferable to use a syringe large enough to draw the full solution. This will reduce the exposure of your product to air. If drawing more than 3 mL at a time, you will want an extra needle to use for equalizing the pressure (you should leave it in the rubber while drawing from the vial). Be careful not to touch critical surfaces (the exposed needle, rubber stopper) while filtering.
Begin by drawing the steroid solution into the syringe. When you are done, remove the needle and attach your newly unwrapped syringe filter. Attach a new needle to the end of the filter, and inject the solution into the new sterile vial. The sterile vial and new needle are very important, as using the original components would only expose the product to bacteria again. Use enough pressure to empty the syringe into the vial. Be careful, as too much pressure can break the bindings or filter. The process is slow, especially with a larger syringe or small .22-micron filter. Provided great care was taken not to contaminate the steroid during the process, the resulting solution should be free of bacteria.
Also, these sterilization methods are applicable to oil-based steroids only. Heat sterilization (as outlined here) tends to cause the rapid evaporation of solvents/antimicrobial agents in water-based steroids. The suspended (instead of dissolved) nature of the particles also makes them likely to jam a syringe filter. Previous testing suggests there is a high prevalence of bacteria in counterfeit and underground water-based steroids.375 Given this, it is generally advised to only use water-based steroids if they have been dispensed through legitimate supply channels.
Stanozolol (Winstrol) 50mg ml(water based) Order Process
1. email or whatsapp us about what you need,quantity and destination.
2. we would answer your email in 12 hours with our best price.
3. If you think the price is workable, we would send you our payment information.
4. After we received your payment ,we would arrange the shipping for you
5. You would receive our package in 7-10 working days.
Stanozolol (Winstrol) 50mg ml(water based) Our Advantage
1. Top Quality in the market, most product have the purity of 98%+ and some beyond 99%
2. Competitive price, we offer speical discount for large amount order.
3. Fast shipping ,we would deliver your product in 7-10 working days.
4. Free Re-shipping, we promise that you will receive your package
5. Security, we will not transfer any of your info to any third party.